External ID: FATTTLab-Algae-Lipid

Protocol: Cells were pre-grown to mid-log phase in TAP media. For primary screen, cells were seeded at low density of 500,000 / well in 384-well plate. Compound in DMSO was added to each well at a final concentration of 10 micromolar and cells were allowed to grow for 72 hours. At the end of assay, Nile Red (30 uM f.c.) was added and plates were incubated at 37 C for 60 mins in dark. Fluorescence intensity was measured. Readouts were reported as normalized fold change in the intensity of treated versus control.

Comment: Reference:
1. Wase, N., Tu, B., Black, P. N. & DiRusso, C. C. Phenotypic screening identifies Brefeldin A/Ascotoxin as an inducer of lipid storage in the algae Chlamydomonas reinhardtii. Algal Research 11, 74-84 (2015).

2. Identification and metabolite profiling of chemical activators of lipid accumulation in green algae
#Nishikant Wase, Boqiang Tu, James W Allen, Paul N Black, Concetta C DiRusso
#Plant Physiology Jun 2017, pp.00433.2017; DOI: 10.1104/pp.17.00433
#http://www.plantphysiol.org/content/early/2017/06/26/pp.17.00433

Patent:
DiRusso, C., & Wase, N. (2016). Compounds for Increasing Lipid Synthesis and Storage. United States#NUtech Ventures (Lincoln, NE, US) http://www.freepatentsonline.com/y2016/0312253.html

For additional Information please contact:

Prof. Concetta C. DiRusso
Department of Biochemistry
University of Nebraska-Lincoln
cdirusso2@unl.edu

Nishikant Wase, PhD
Department of Biochemistry
University of Nebraska-Lincoln
nishikant.wase@gmail.com

External ID: TargetID_659_CEMA

Protocol: Black, standard capacity streptavidin-coated 384-well plates (Pierce 15407) were first washed with 50 L of phosphate buffer (100 mM, pH 7.0; PB7) three times using a Biotek 405 ELX plate washer. Subsequently, 5 L of biotinylated pre-miRNA substrate (500 nM final) was dispensed into the plate using a Multidrop Combi Reagent Dispenser (Thermo Scientific). Plates were then centrifuged for 1 min at 1,000 RPM (223 g), sealed with plate tape, and incubated overnight at 4 C. The following morning, plates were washed three times with 50 L of PB7, followed by the addition of 5 L of Dicer digest buffer (20 mM Tris, 12 mM NaCl, 2.5 mM MgCl2, 1 mM fresh DTT, and 4.5% DMSO) and centrifugation. Compounds (50 nL of 5 mM DMSO stock, 25 M final) were then added into the sample wells using a Sciclone (Caliper) liquid handler with V&P pintool; the same volume of DMSO was added to the control wells. The plates were incubated at 25 C for 15 min before addition of 5 L of digest buffer containing 217 g/nL Dicer (108 g/mL Dicer, 5% glycerol and 0.01% Triton X-100 final, excess with respect to pre-miRNA). For the positive control wells, digest buffer without Dicer was added. The plates were centrifuged again and resealed before being placed in a 37 C incubator for 5 h. After Dicer cleavage, plates were washed three times with 50 L of PB7. mTet-HRP in PB7 (10 L, 750 nM final) was then dispensed into each well. The plates were subsequently centrifuged, sealed, and incubated at 25 C for 2 h. Plates were then washed three times with 50 L of wash buffer (2 mM imidazole, 260 mM NaCl, 0.5 mM EDTA, 0.1% Tween-20, pH 7.0), followed by washing three additional times with 50 L of PB7. Finally, SuperSignal West Pico (25 L; Pierce) was added, the plates were incubated at 25 C for 5 min, and chemiluminescence signal was detected using a PHERAstar plate reader using LUM plus module (BMG Labtech).

Comment: The activity outcome is based on a Z-score (number of standard deviations from the negative control mean) of 3 or higher on at least 50% times that the sample was screened.

For instance, if the sample was screened in n=4 runs, it would be considered active only if it had a Z-score of 3 or above in at least 2 runs.

External ID: KUHTS-Muma KU-CaM-Htt INH-01

Protocol: 1; Dispense 45 nl compounds (10 mM stocks) using ECHO 555 to Alpha 384 well assay plates. Dispense 45 nl DMSO to control columns 1 and 2 of 384 well plates.
2; Incubate 5 ul of 6XHis-mHTT (Final, 13 nM) with the compounds for 40 mins at room temperature in buffer containing 10 mM Tris.HCl pH 7.4, 1 mM calcium chloride, 150 mM sodium chloride, 0.1% BSA and 20% glycerol.
3; Dispense 5 ul of 6XGST-CaM (Final 13 nM) in buffer A.
4; Incubation; 1 hour (dark at 25C)
5; Dispense 20 ul of Nickel chelate acceptor beads (Final, 20 ugs/ml) and Glutathione donor beads (Final, 30 ugs/ml). Incubate for 2h, room temperature.
6; Detector: Perkin Elmer Enspire, Alphascreen Module (Excitation 680nm/Emission 570nm).

NOTES (numbers refer to Sequence numbers above)
1. Alphascreen bead incubations were performed in green light, TiterTek setting 400rpm.
2. All incubation and addition steps were followed by mixing and centrifugation at 400g,1 min.
3. The percent inhibition for each compound was calculated as follows:
100- [100 *((Test Compound-Median Low Control) / (Median High Control - Median Low Control))]

Where:
Test_Compound is defined as wells containing His mHTT + GST CaM in the presence of test compound

High_Control is defined as wells containing His mHTT + GST CaM and DMSO.

Low_Control is defined as wells containing His mHTT and DMSO.

Comment: All percent inhibition data reported were normalized to high and low controls on a per-plate basis. The results of primary screening data include compounds contributing to assay signal interference, interference with tags binding to Alpha beads, chelators, process related artifacts etc.. The actives were defined as compounds that inhibited Alphascreen reads to greater than 50%.