External ID: JHICC_RGS_Act_HTS

Protocol: Assay overview:

To screen for compounds that activate the RGS4 protein, a HEK293 cell line which stably expresses M3R and inducibly expresses RGS4 is employed. RGS4 function is monitored by calcium flux with a commercially available Fluo4-AM dye. Compounds that do not show increase in the Fluo4 fluorescence in induced RGS4 expressed cells are considered as activator/potentiator hits. M3 receptor and other endogenous receptor activators/potentiators will be excluded through later counter-screening against non-induced parental cells.

Protocol for RGS4 Primary Screen:
1. Cell culture: Cells (HEK293-FlpIn-TREx/M3R/RGS4) are routinely cultured in DMEM (high glucose, w/ glutamine), 10%FBS, 1%Pen/Strep, 15ug/ml Blasticidin, 400ug/ml G418, 200ug/ml Hygromycin.
2. Cell plating: Add 50 ul/well of 200,000 cells/ml re-suspended in DMEM/high glucose medium with 10% FBS, 1% Pen/Strep. Include 10 ng/ml Doxycyclin (DOX) to induce RGS4 expression.
3. Incubate overnight at 37C and 5% CO2.
4. Remove medium and add 20 ul /well of 2uM Fluo4-AM solution to cells.
5. Incubate 30 minutes at 37C in incubator.
6. Prepare 6x compound plates and control plates on Cybi-Well system: test compounds are prepared using assay buffer (HBSS-HEPES pH 7.4).
7. Remove Fluo4-AM dye solution and add 20 ul/well of assay buffer to cells.
8. Incubate 30 minutes at room temperature (RT).
9. Add 6x compounds in cell plates and incubate 20 minutes at RT.
9. Load cell plates on Hamamatsu FDSS 6000 kinetic imaging plate reader
10. Measure fluorescence for 10 seconds at 1Hz to establish baseline
11. After 100 seconds, add 4 ul of ECmax (carbachol) into the cell plates and record fluorescence for 100 seconds.
12. Calculate ratio readout as F(max-min)/F0 and integrated ratio readout.
13. Calculate the average and standard deviation for negative and positive controls in each plate, as well as Z and Z' factors [26]
14. Calculate B scores [27] for test compounds using integrated ratios calculated in Step 12
15. Outcome assignment: If the B score of the test compound is less than 4 times the standard deviation (SD) of the B scores of integrated ratios of all library compounds above the mean (B score Activator Ratio16. Score assignment: An active test compound is assigned a score between 5 and 100 by calculation of Int(((Log(ABS(B score ratio))-0.82)/0.44)*100), and they are normalized to the smallest and largest LOG(B score ratio), B score ratio, as in the result definition. The inactive test compounds are assigned a score of 0.


List of reagents

1. HEK293-FlpIn-TREx/M3R/RGS4 cell lines (provided by assay provider)
2. PBS: pH7.4 (Invitrogen Cat#10010049)
3. Medium: DMEM (Sigma, Cat#D5796)
4. Fetal Bovine Serum (Gemini, Cat# 100-106)
5. Hygromycin (Mediatech, Cat#30-240-CR)
6. 100x Penicillin-Streptomycin (Mediatech, Cat#30-001-CI)
7. Cell/stripper (Mediatech, Cat#25-056-Cl)
8. G418: (Invitrogen, Cat#11811-031)
9. Blasticidin (Sigma, Cat#R21001)
10. Doxycycline hyclate (Sigma, Cat#D9891)
11. HEPES (Sigma, Cat#H4034)
12. Fluo-4 (Invitrogen, Cat #F14202)
13. Pluronic F-127*20% in DMSO (Invitrogen, Cat#P-3000MP)
14. Atropine (Sigma, Cat#A0132)
15. Carbachol (Sigma, Cat# C4382)
16. Triple-layer flask (VWR, Cat #62407-082)
17. BD Biocoat 384-well plates (BD, Cat# (35)4663 and Lot #7346273)

Comment: To screen for compounds that activate the RGS4 protein, a HEK293 cell line which stably expresses M3R and inducibly expresses RGS4 is employed. RGS4 function is monitored by calcium flux with a commercially available Fluo4-AM dye. Compounds that do not show increase in the Fluo4 fluorescence in induced RGS4 expressed cells are considered as activator/potentiator hits. M3 receptor and other endogenous receptor activators/potentiators will be excluded through later counter-screening against non-induced parental cells.

External ID: OPRM1-OPRD1_AG_LUMI_1536_1X%ACT PRUN

Protocol: Assay Overview:

The purpose of this assay is to identify compounds that activate heterodimer formation between the mu (OPRM1) and delta (OPRD1) opioid receptors, resulting in membrane recruitment of beta-arrestin. The assay monitors GPCR-beta-arrestin proximity using low affinity fragment complementation of beta-galactosidase (beta-gal). This assay employs U2OS cells which express OPRD1, OPRM1 fused to a beta-gal peptide fragment (enzyme donor), and beta-arrestin fused to the complementary beta-gal fragment (enzyme acceptor). Cells are incubated with test compound, followed by measurement of well luminescence. As designed, compounds that induce formation of OPRD1 homodimers or OPRM1-OPRD1 (Mu-Delta) heterodimers will cause beta-arrestin recruitment, resulting in reconstitution of the beta-gal holoenzyme. The reconstituted holoenzyme can then catalyze the hydrolysis of a substrate which yields a chemiluminescent signal, resulting in increased well luminescence. Deltorphin B will be used as the high (100% RLU) control for agonists, and wells containing cells treated with DMSO will be used as the low (0% RLU) control. Compounds were tested in singlicate at a final nominal concentration of 9.3 uM.

Protocol Summary:

The U2OS-OPRM1-OPRD1 (Mu-Delta) cell line was routinely cultured in T-175 sq cm flasks at 37 C and 95% relative humidity (RH). The growth media consisted of a 1:1 mixture of Ham's F-12 Nutrient Media (F-12) and Dulbecco's Modified Eagle Media (DMEM) supplemented with 10% v/v heat-inactivated certified fetal bovine serum, 25 mM HEPES, 250 ug/mL Geneticin, 250 ug/mL Hygromycin B, 0.25 ug/mL Puromycin and 1X antibiotic mix (penicillin, streptomycin, and neomycin).

The day before the assay 1000 cells in 3 uL of cell plating media were seeded into each well of 1536 well microtiter plates and allowed to incubate at 37 C, 5% CO2, and 95 % RH for 23 hours. Next, 28 nL of test compound in DMSO, Deltorphin B (0.9 uM final concentration) in DMSO, or DMSO alone were dispensed to the appropriate wells. The plates were then incubated for 3 hours at 37 C, 5% CO2, and 95 % RH. The assay was started by adding 2 uL of PathHuntertrade mark reagent (prepared according to the manufacturer's protocol); followed by 1 hour incubation at room temperature. Then, Well Luminescence was read on the ViewLux plate reader

The percent activation for each compound was calculated as follows:

% Activation = ( ( Ratio_Test_Compound - Median_Ratio_Low_Control ) / ( Median_Ratio_High_Control - Median_Ratio_Low_Control ) ) * 100

Where:

High_Control is defined as wells containing cells, Deltorphin B and DMSO.
Test_Compound is defined as wells containing cells, test compounds and DMSO.
Low_Control is defined as wells containing cells and DMSO.

A mathematical algorithm was used to determine nominally activating compounds in the primary screen. Two values were calculated: (1) the average percent activation of all compounds tested, and (2) three times their standard deviation. The sum of these two values was used as a cutoff parameter, i.e. any compound that exhibited greater % activation than the cutoff parameter was declared active.

PubChem Activity Outcome and Score:

The reported PubChem Activity Score has been normalized to 100% observed primary activation. Negative % activation values are reported as activity score zero.

The PubChem Activity Score range for active compounds is 100-2, and for inactive compounds 2-0.

List of Reagents:

PathHuntertrade mark B-arrestin recruitment assay, containing the U2OS OPRM1 OPRD1 Beta-arrestin cell line; PathHunter Detection Kit (DiscoveRx, part, 93-0558C3)
Ham's F-12 media (Invitrogen, part 11765-054)
DMEM media (Invitrogen, part 11995-073)
Detachin (Genlantis, part T100100)
Heat Inactivated Fetal Bovine Serum (Invitrogen, part 10082-147)
Puromycin (Invitrogen, part A11138-02)
Hygromycin B (Invitrogen, part 10687-010)
Geneticin (Invitrogen, part 10131-027)
100X Penicillin-Streptomycin-Neomycin mix (Invitrogen, part 15640-055)
T-175 tissue culture flasks (Nunc, part 159910)
Agonist: Deltorphin B (Anaspec, part 62683)
1536-well plates (Greiner, part 789173)

Comment: Due to the increasing size of the MLPCN compound library, this assay may have been run as two or more separate campaigns, each campaign testing a unique set of compounds. All data reported were normalized on a per-plate basis. Possible artifacts of this assay can include, but are not limited to: dust or lint located in or on wells of the microtiter plate, and compounds that modulate well fluorescence. All test compound concentrations reported above and below are nominal; the specific test concentration(s) for a particular compound may vary based upon the actual sample provided by the MLSMR.

External ID: ERK5 transcriptional activity-HTS

Protocol: Stable cells plated on a 384-well plate (2500 cells/well) were treated with test compounds at the concentration of 5 muM for 18 hrs. The level of luciferase activity was assayed using a
Luciferase kit (Promega corporation, Madison, WI) and a series of positive and negative control compounds were used as references.

Comment:

External ID: CHRM1_AG_FLUO8_1536_1X%ACT PRUN

Protocol: Assay Overview:

The purpose of this assay is to identify compounds that act as agonists of the human M1 muscarinic receptor (CHRM1; M1). In this assay, CHO-K1 cells stably expressing human M1 are loaded, intracellularly with the calcium indicator dye, Fluo-8, followed by treatment with agonist control or test compounds. As designed, compounds that act as CHRM1 agonists will increase intracellular calcium mobilization, resulting in increased relative fluorescence of the indicator dye and well fluorescence. Compounds are tested in singlicate at a final nominal concentration of 3 uM.

Protocol Summary:

The CHO-hM1 cell line was routinely cultured in T-175 sq cm flasks at 37 C and 95% relative humidity (RH). The growth media consisted of Ham's F-12 Nutrient Media (F-12) supplemented with 10% v/v heat-inactivated qualified fetal bovine serum, 20 mM HEPES, 50 ug/mL Geneticin, and 1X antibiotic mix (penicillin and streptomycin).

The day before the assay 3000 cells in 3 uL of growth media were seeded into each well of 1536 well microtiter plates and allowed to incubate at 37 C, 5% CO2, and 95 % RH for 17-24 hours. Next, 2 uL of the fluorogenic Fluo-8 intracellular calcium indicator mixture (prepared according to the manufacturer's protocol) was added to each well. Plates were then incubated for 1 hour at 37 C, 5% CO2, and 95 % RH, followed by 30 minute incubation at room temperature. Then, 15 nL of test compound in DMSO were dispensed to appropriate wells. The assay was started by performing a basal read of plate fluorescence (470-495 nm excitation and 515-575 nm emission) for 5 seconds on the FLIPR Tetra (Molecular Devices). Then a real time fluorescence measurement was immediately performed for the remaining 140 seconds of the assay. A ratio for each well was calculated to normalize assay data, according to the following mathematical expression:

Ratio = I_Max / I_Min

Where:

I_Max represents the maximum measured fluorescence emission intensity over the 140 second read.
I_Min represents the minimum (basal) measured fluorescence emission intensity before compound was added.

The percent activation was calculated from the median ratio as follows:

%_Activation = ( ( Ratio_Test_Compound - Median_Ratio_Low_Control ) / ( Median_Ratio_High_Control - Median_Ratio_Low_Control ) ) * 100

Where:

Test_Compound is defined as wells containing test compound.
Low_Control is defined as wells containing DMSO.
High_Control is defined as wells containing Acetylcholine (EC100) and DMSO.

PubChem Activity Outcome and Score:

A mathematical algorithm was used to determine nominally activating compounds in the primary screen. Two values were calculated for each assay plate: (1) the average percent activation of test compound wells and (2) three times their standard deviation. The sum of these two values was used as a cutoff parameter for the entire run, i.e. any compound that exhibited greater % activation than the entire screen's cutoff parameter was declared active.

The reported PubChem Activity Score has been normalized to 100% observed primary activation. Negative % activation values are reported as activity score zero.

The PubChem Activity Score range for active compounds is 100-1, and for inactive compounds 1-0.

List of Reagents:

Cell line: Chinese Hamster Ovary (CHO) cells containing hM1 receptor; (Conn Lab)
Calcium sensitive dye: Fluo-8 No Wash Calcium Assay Kit; (AAT Bioquest, part 36316)
Growth media: Ham's F-12; 10% FBS, 20mM HEPES, 50 ug/mL G418
Assay media: Ham's F-12, 10% FBS, 20 mM HEPES
Assay plates: Aurora black/clear 1536well FLIPR plate; (Aurora, part 00019326)
Probenecid: 250 mM (pH 8.0); (Sigma P8761)
Agonist: Acetylcholine (50 mM stock in water); Sigma A9187

Comment: Due to the increasing size of the MLPCN compound library, this assay may have been run as two or more separate campaigns, each campaign testing a unique set of compounds. All data reported were normalized on a per-plate basis. Possible artifacts of this assay can include, but are not limited to: dust or lint located in or on wells of the microtiter plate, and compounds that modulate well fluorescence. All test compound concentrations reported above and below are nominal; the specific test concentration(s) for a particular compound may vary based upon the actual sample provided by the MLSMR.

External ID: BCCG-A405-UPR-XBP1-PrimaryAgonist-Assay

Protocol: UPR CHO-XBP1 1536-Well Assay Protocol
A. Brief Description of the Assay:
The purpose of this assay is to detect activators of the IRE1-XBP1 (adaptive) arm of the Unfolded Protein Response pathway.
B. Materials:
CHO-XBP1 Cell Line
F12 nutrient mix HAMs (Invitrogen, Cat# 11765047)
Fetal Bovine Serum, heat-inactivated (Hyclone, Cat# SH30396)
Penicillin/Streptomycin, liquid (Invitrogen, Cat# 15140122)
L-glutamine (100X ) (Invitrogen, Cat# 25030081)
MEM Non-Essential Amino Acids Solution 10 mM (100X) (Invitrogen, Cat# 11140050)
Trypsin-EDTA 0.25% (Invitrogen, Cat# 25200-056)
DPBS (Hyclone, Cat# 30028.02)
T225 TC Flask (Nunc, Cat# 159934)
Cell strainer, 40 um (BD, Cat# 352340)
Aurora 1536 well white solid bottom TC plate (Aurora Biotechnology 00029846)
Tunicamycin (Sigma-Aldrich, Cat# T7765)
Steady-Glo Luciferase Assay System (1L) (Promega, Cat# E2550)

C. Plate Map:
Positive control (P) in columns 1 and 2, 10ug/mL Tunicamycin
Negative control (N) in columns 3 and 4, No Tunicamycin
Test compound (T) in columns 5 - 48, No Tunicamycin

D. Procedures:
Day1 Cell Seeding
1. Prepare cell suspensions as described in section F. Cell culture.
2. Set up Kalypsys dispenser as described in section G. Kalypsys dispenser setting.
3. Plate 1000 cells/well in 5 uL of assay media into columns 1-48 of a 1536-well assay plate, using straight tip dispense on a Kalypsys dispenser.
4. Centrifuge plates at 500 rpm for 1 minute on Eppendorf centrifuge 5810. Use Kalypsys metal lids.
5. Incubate overnight at 37 degrees, 100% relative humidity, 5% CO2 for 16-18 hours.

Day2 Compound Addition
6. Using LabCyte Echo, transfer 50 nL from a 2 mM Echo qualified plate containing test compounds into assay plate Col. 5 - 48 (final concentration of test compounds is 20 uM, 1% DMSO), 50 nL of 1 mg/mL Tunicamycin in DMSO to positive control wells in Columns 1 and 2, and 50 nL of DMSO to negative control wells in Columns 3 and 4.
7. Centrifuge plates at 1000 rpm for 1 minute on a Vspin centrifuge.
8. Incubate plates in incubator (37 degrees, 100% relative humidity, 5% CO2) for 6 hours.
9. Set up Kalypsys dispenser and Perkin Elmer Envision as described in section G. Kalypsys dispenser setting and H. Envision setting.
10. Following 6 hours incubation, remove lid and incubate plate for 10 min in at room temp.
11. Add 3 uL of Steady-Glo to each wells (Columns 1 - 48) using a Kalypsys dispenser.
12. Centrifuge plates at 2000 rpm for 2 minutes on a Vspin centrifuge.
13. Lid plate and incubate for 10 min at room temp.
14. Read plates using Envision using a luminescence protocol.
E. Recipe:
Growth Media
F12 nutrient mix HAMs supplemented with 10% hi-FBS, 1X Penicillin/Streptomycin, 1X L-glutamine, and 1X MEM-NEAA
Assay Media
Filtered Growth Media
Trypsin
Dilute 0.25% Trypsin/EDTA to 0.05% Trypsin/EDTA using DPBS
Positive Control
Tunicamycin at 10 ug/mL final.
(Note: Tunicamycin is reconstituted in DMSO to a concentration of 10mg/ml).

F. Cell Culture:
Prepare Growth Media/Assay Media as described in section E. Recipe.
Procedure to expand and maintain cells:
CHO-CHOP cells are seeded into T225 flasks at 3.75 x 105 cells. Cells are passaged twice a week (Monday or Tuesday, and Thursday or Friday depending on cell growth). Confluency should be maintained at <75%. After 3 days incubation, ~2.5X10^7 cells are expected per T225 flask. Incubate cells in 5% CO2.
1. Put media in water bath and leave for 30 minutes. Also leave Trypsin at room temp for 15 minutes. Keep DPBS at room temp (no need to warm up DPBS at 37 degrees).
2. Aspirate off old media from T225 flask.
3. Wash the flasks with 20 mL DPBS per T225 flask. Leave cells in DPBS for about 30 seconds.
4. Add 6.5 mL 0.05% Trypsin solution into the flask. Rock the flask gently so that the solution covers all over the surface.
5. Allow the cells to detach by incubating at room temperature for about 4 minutes.
6. Wash the flask with 25 mL fresh growth media.
7. Collect the cell suspension in a 50 mL sterile conical tube.
8. Centrifuge at 900 rpm for 5 minutes. Once pelleted, remove the supernatant and resuspend the cell pellet carefully in 1 mL fresh growth media with p1000 pipette.
9. Add 19 mL of growth media and mix gently.
10. Filter the cell suspension with cell strainer.
11. Count the cells and prepare stock flasks with
3.00 x 10^5 cells per T225 flask for 4 days incubation.
3.75 x 10^5 cells per T225 flask for 3 days incubation.
Procedure to prepare cells for the assay:
Follow steps 1 - 3 above
4. Add 5 mL Trypsin into the flask. Rock the flask gently so that the solution covers all over the surface.
5. Allow the cells to detach by incubating at room temperature for about 4 minutes.
6. Wash the flask with 25 mL fresh growth media.
7. Collect the cell suspension in a 50 mL sterile conical tube.
8. Centrifuge at 500 rpm for 10 minutes. Once pelleted, remove the supernatant and resuspend the cell pellet carefully in 1 mL fresh assay with p1000 pipette.
9. Add 19 mL of assay media and mix gently.
10. Filter the cell suspension with cell strainer.
11. Count the cells and adjust cell density to 1.0x10^5 cells/mL in media.

Comment: Compounds that test with activity greater than or equal to 30% activation at 20 uM concentration relative to the positive control are defined as actives in the primary assay.
To simplify the distinction between the inactives of the primary screen and of the confirmatory screening stage, the Tiered Activity Scoring System was developed and implemented. Its utilization for the assay is described below.

Activity Scoring
Activity scoring rules were devised to take into consideration compound efficacy, its potential interference with the assay and the screening stage that the data was obtained. Details of the Scoring System will be published elsewhere. Briefly, the outline of the scoring system utilized for the assay is as follows:
1) First tier (0-40 range) is reserved for primary screening data. The score is correlated with % activity in the assay demonstrated by a compound at 20 uM concentration:
a. If outcome of the primary screen is inactive, then the assigned score is 0
b. If outcome of the primary screen is inconclusive, then the assigned score is 10
c. If outcome of the primary screen is active, then the assigned score is 20
Scoring for Single concentration confirmation screening is not applicable to this assay.
d. If outcome of the single-concentration confirmation screen is inactive, then the assigned score is 21
e. If outcome of the single-concentration confirmation screen is inconclusive, then the assigned score is 25
f. If outcome of the single-concentration confirmation screen is active, then the assigned score is 30
This scoring system helps track the stage of the testing of a particular SID. For the primary hits which are available for confirmation, their scores will be greater than 20. For those which are not further confirmed, their score will stay under 21.
2) Second tier (41-80 range) is reserved for dose-response confirmation data and is not applicable in this assay
3) Third tier (81-100 range) is reserved for resynthesized true positives and their analogues and is not applicable in this assay

External ID: CHEMBL4150189

Protocol: N/A

Comment: Compounds with activity <= 10uM or explicitly reported as active by ChEMBL are flagged as active in this PubChem assay presentation.

Journal: J Nat Prod
Year: 2018
Volume: 81
Issue: 6
First Page: 1460
Last Page: 1467
DOI: 10.1021/acs.jnatprod.8b00227

Target ChEMBL ID: CHEMBL335
ChEMBL Target Name: Protein-tyrosine phosphatase 1B
ChEMBL Target Type: SINGLE PROTEIN - Target is a single protein chain
Relationship Type: D - Direct protein target assigned
Confidence: Direct single protein target assigned

External ID: MH080376 Biochemical HTS for Inhibitors of the Proprotein Convertase Furin.

Protocol: Biochemical Furin HTS Assay protocol

Reaction Buffer Concentrations (final concentrations): 50 mM Hepes pH 7.5, 1 mM CaCl2, 1 mM beta-mercaptoethanol , 0.2 mg/ml BSA.

Substrate Stock Solution: 10 mM pERTKR-AMC in DMSO; stored in aliquots at -20 oC.

rhFurin714 prep (5.2 units/uL)Stored in aliquots at -80oC.

Furin Assay Protocol

The assay involves three liquid transfer steps of 5 uL each of 30 uM compound in 1% DMSO (10 uM final), 1 unit/5 uL rhFurin714 in 3X reaction buffer and 5 #L of 30 uM pERTKR-AMC substrate (10 uM final).

The assay plates used are Greiner 384-well, flat-bottom, low volume, black polystyrene plates (VWR catalog # 784076).

1. Add 5 uL of compound/controls to each well.
2. Add 5 uL of rhFurin714 in 3X buffer (1.0 units/well final).
3. Add 5 uL of 30 uM pERTKR-AMC fluorigenic substrate (10 uM/well final).
4. Incubate the plates for 1 hr at room temperature.
5. Stop the reaction by adding 5 uL of 1M Acetic acid.
6. Measure the amount of fluorigenic AMC released on the SpectraMax M5 using Ex = 345nm; Em = 440nm; cut-off 420 nm.

Comment: Active Criteria, Secondary Assay Plan, Hit and Lead Criteria.

Furin HTS Activity scoring rules:

The Furin inhibitor HTS run at the PMLSC utilized % inhibition calculated from maximum (n=32) and minimum (n=24) plate controls, with a hit criteria of >/= 25% inhibition to identify active compounds.

Furin Inhibitor scoring rules:

PUBCHEM_ACTIVITY_OUTCOME

1 - Substance is considered inactive when the % inhibition is < 25 %
2 - Substance is considered active when % activation is >/= 25 %
3 - Substance activity outcome is inconclusive

PUBCHEM_ACTIVITY_SCORE

0-40 scoring range is reserved for primary HTS data
a) if the % inhibition is >/= 25 %, the score is 40.
b) if the % inhibition is < 25 %, the score is 0.

Definition of Hit Criteria:
It is anticipated that all Furin inhibitor HTS actives will be confirmed in duplicate at the primary HTS concentration of 30 uM.
Furin inhibitor actives confirmed in the primary HTS format will then be run in 10-pt IC50 concentration response curves.
Confirmed hits will be subjected to structural confirmation by LCMS.

Secondary assay testing paradigm: Confirmed concentration dependent Furin inhibitors will be tested in the HeLa pcFur1.6 cell based ELISA assay.

External ID: 2147-01_Inhibitor_SinglePoint_HTS_Activity

Protocol: Protocol:
The FadD28 is purified through Ni-NTA affinity column due to a 6x Histidine tag. Purified protein is stored at -80 degrees C (D.J. Wilson, and C.C. Aldrich. Anal. Biochem. 404 (2010) 56-63)
I. Solution preparation (For a run of 121 plates):
1) Prepare 700mL of 200nM compound 11 (TAMRA labeled substrate) in FP buffer. Take 1.4mL of 100uM compound 11 in 100% DMSO in 700mL FP buffer
2) Prepare 50mL compound24 (non-labeled substrate) in FP buffer. Take 200uL of 10mM compound 24 in 100% DMSO in 50mL FP buffer
3) Prepare 350mL 4uM FadD28 in FP buffer. Take 1.746mL of 802uM FadD28 in 350mL FP buffer
II. Setup reagents on automation instrument
1) Add the solutions of compound24, FadD28 and FP buffer to the bottles of BioRaptr (Beckman) based on the dispense table
2) Add compound 11 solution to the bottle of combi NL (Thermo Scientific)
3) Add 1536-well assay ready plates (ARPs) to incubator
III. Run automation protocol
1) Dispense 3uL/well of the solutions from BioRaptr based on the dispense table to 1536-well assay ready plates (ARPs) (Aurora, Cat#: 00019180BX)(Positive control wells receive 1.5uL/well of compound24 and 1.5uL/well of FadD28 solution; all the other wells receive 1.5uL/well of FP buffer and 1.5uL/well of FadD28 solution)
2) Incubate the plates for 10mins at 25 degrees C
3) Dispense 3uL/well of 200nM compound11 solution to the plates by Combi NL
4) Incubate the plates for 30mins at 25 degrees C
5) Read the plates on ViewLux (PerkinElmer) with excitation wavelength of 525nm, emission wavelength of 598 nm and dichroic mirror of 550nm
Final concentration: 100nM compound11, 1uM FadD28, 10uM compound24 (positive control), compound concentration for primary screen: 12.5uM
FP buffer: 30mM Tris-HCl, pH7.5, 1mM MgCl2, 1mM DTT, 0.0025% Igepal CA630

Comment: PRESENCE OF CONTROLS: Neutral control wells (NC) and positive control wells (PC) were included on every plate.

EXPECTED OUTCOME: Active compounds result in decreasing readout signal.

NORMALIZATION:
The raw signals of the plate wells were normalized using the 'Neutral Controls Minus Inhibitors' method in Genedata Assay Analyzer (v7.0.3):
The median raw signal of the intraplate neutral control wells was set to a normalized activity value of 0.
The median raw signal of the intraplate positive control wells was set to a normalized activity value of -100.
Experimental wells values were scaled to this range.
All well activities were then multiplied by -1 to create a positive activity readout value range, to match Pubchem convention.


PATTERN CORRECTION: No plate pattern correction algorithm from Genedata Condoseo (v.7.0.3) was applied.

PUBCHEM_ACTIVITY_SCORE:
This was set as equal to the maximum of the normalized sample replicate activities, rounded to the nearest integer .
The minimum PUBCHEM_ACTIVITY_SCORE required for a compound to be called a hit (the activity threshold, or AT) was set at 8.

PERCENTAGE OF ACTIVE REPLICATES:
For each sample, the percentage of replicates (PCT_ACTIVE_REP) which had activity scores >= AT was determined.
The minimum percentage of replicates required for a compound to be called a hit (PAR_T) was set at 100.

PUBCHEM_ACTIVITY_OUTCOME:
Samples passing BOTH threshold criteria were assigned an outcome of 2 (active):
PUBCHEM_ACTIVITY_SCORE >= AT, and PCT_ACTIVE_REP >= PAR_T

Samples passing NEITHER threshold criteria were assigned an outcome of 1 (inactive):
PUBCHEM_ACTIVITY_SCORE < AT, and PCT_ACTIVE_REP < PAR_T

Samples passing AT only were assigned an outcome of 3 (inconclusive) :
PUBCHEM_ACTIVITY_SCORE >= AT, and PCT_ACTIVE_REP < PAR_T

tSamples passing PAR_T only were assigned an outcome of 3 (inconclusive) :
PUBCHEM_ACTIVITY_SCORE < AT, and PCT_ACTIVE_REP >= PAR_T

External ID: CHRM1_PAM_FLUO8_1536_1X%ACT PRUN

Protocol: Assay Overview:

The purpose of this assay is to identify compounds that act as positive allosteric modulators (PAMs) and increase activity of the human M1 muscarinic receptor (CHRM1; M1) in cells pre-treated with a known agonist. In this assay, CHO-K1 cells stably expressing human M1 are loaded with the Fluo-8 calcium indicator dye, followed by addition of test compounds and subsequent treatment with the activator acetylcholine at a concentration that results in 20% activation (EC20). As designed, compounds that act as CHRM1 PAMs will increase calcium mobilization, resulting in increased intracellular calcium and relative fluorescence of the indicator dye beyond that of the EC20 of acetylcholine. Compounds are tested in singlicate at a final nominal concentration of 3 micromolar.

Protocol Summary:

The CHO-hM1 cell line was routinely cultured in T-175 sq cm flasks at 37 degrees C and 95% relative humidity (RH). The growth media consisted of Ham's F-12 Nutrient Media (F-12) supplemented with 10% v/v heat-inactivated qualified fetal bovine serum, 20 mM HEPES, 50 micrograms/mL Geneticin, and 1X antibiotic mix (penicillin and streptomycin).

The day before the assay 3000 cells in 3 microliters of growth media were seeded into each well of 1536 well microtiter plates and allowed to incubate at 37 degrees C, 5% CO2, and 95 % RH for 17-24 hours. Next, 2 microliters of the fluorogenic Fluo-8 intracellular calcium indicator mixture (prepared according to the manufacturer's protocol) was added to each well. Plates were then incubated for 1 hour at 37 degrees C, 5% CO2, and 95 % RH, followed by 30 minute incubation at room temperature. Then, 15 nL of test compound in DMSO were transferred to appropriate wells. The assay was started by performing a basal read of plate fluorescence (470-495 nm excitation and 515-575 nm emission) for 5 seconds on the FLIPR Tetra (Molecular Devices) prior to all wells being treated with an EC20 concentration of acetylcholine. Then a real time fluorescence measurement was immediately performed for the remaining 140 seconds of the assay. A ratio for each well was calculated to normalize assay data, according to the following mathematical expression:

Ratio = I_Max / I_Min

Where:

I_Max represents the maximum measured fluorescence emission intensity over the 140 second read and;
I_Min represents the minimum (basal) measured fluorescence emission intensity before compound was added.

The percent activation was calculated from the median ratio as follows:

% Activation = ( ( Ratio_Test_Compound - Median_Ratio_Low_Control ) / ( Median_Ratio_High_Control - Median_Ratio_Low_Control ) ) * 100

Where:

Test_Compound is defined as wells containing test compound.
Low_Control is defined as wells containing Acetylcholine at EC20 and DMSO.
High_Control is defined as wells containing Acetylcholine (EC100) and DMSO.

A mathematical algorithm was used to determine nominally activating compounds in the primary screen. Two values were calculated for each assay plate: (1) the average percent activation of test compound wells and (2) three times their standard deviation. The sum of these two values was used as a cutoff parameter on an individual plate basis, i.e. any compound that exhibited greater % activation than the plate based cutoff parameter was declared active.

PubChem Activity Outcome and Score:

The inactive compounds of this assay have an activity score range of 0 to 78 and the active compounds have an activity score range of 50 to 100.

The reported PubChem Activity Score has been normalized to 100% observed primary activation. Negative % activation values are reported as activity score zero.

List of Reagents:

Cell line: Chinese Hamster Ovary (CHO) cells containing hM1 receptor; (Conn Lab)
Calcium sensitive dye: Fluo-8 No Wash Calcium Assay Kit; (AAT Bioquest, part 36316)
Growth media: Ham's F-12; 10% FBS, 20mM HEPES, 50?g/mL G418
Assay media: Ham's F-12, 10% FBS, 20 mM HEPES
Assay plates: Aurora black/clear 1536well FLIPR plate; (Aurora, part 00019326)
Probenecid: 250mM (pH 8.0); (Sigma P8761)
Potentiator: Acetylcholine (50mM stock in water); Sigma A9187

Comment: Due to the increasing size of the MLPCN compound library, this assay may have been run as two or more separate campaigns, each campaign testing a unique set of compounds. All data reported were normalized on a per-plate basis. Possible artifacts of this assay can include, but are not limited to: dust or lint located in or on wells of the microtiter plate, and compounds that modulate well fluorescence. All test compound concentrations reported above and below are nominal; the specific test concentration(s) for a particular compound may vary based upon the actual sample provided by the MLSMR.

External ID: SAID_488997

Protocol:

Comment:

External ID: epac1-activator-v

Protocol: Briefly, three uL of reagents (100 nM EPAC1, 250 nM RAP1B-BODIPY-GDP, 50 uM GDP) were dispensed into a 1536-well Greiner black solid-bottom medium binding assay plate. Controls and test compounds (23 nL) were transferred to the plate via a Kalypsys pin tool equipped with a 1536-pin array. The plates were centrifuged at 1,000 rpm for 15 seconds followed by 5 minute incubation at room temperature. The assay plates were read at 5 minute intervals for 30 minutes in the ViewLux plate reader using 480nm excitation and 540nm emission filters. The results were normalized to the agonist positive control of 6.5 mM cAMP.

Comment: Disclaimer:
Although all reasonable efforts have been made to ensure the accuracy and reliability of the data, caution should be exercised when interpreting the results as artifacts are possible from nonspecific effects such as assay signal interference. The curve fitting and activity calls presented here are based on the NCATS analysis methods.

Compound Ranking:
1. Compounds are first classified as having full titration curves, partial modulation, partial curve (weaker actives), single point activity (at highest concentration only), or inactive. For this assay, apparent activators are ranked higher than compounds that showed apparent inhibition.
2. For all inactive compounds, with a ratio activity curve class of 4, PUBCHEM_ACTIVITY_SCORE is 0. For all active compounds, a score range was given for each curve class type given above. Active compounds have PUBCHEM_ACTIVITY_SCORE between 40 and 100. For a ratio activity curve class = 1.1, score = 80+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == 1.2 && abs(ratio.max_response) > 6*10, score = 60+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == 2.1 || ( ratio.curve_class==-2.2 && abs(ratio.max_response) > 6*10), score = 40+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == 1.2 || ratio.curve_class == 2.2, score = 20+abs((log_ac50+4.5)*inf_activity/20). Inconclusive compounds, with a donor curve class other than 4, have PUBCHEM_ACTIVITY_SCORE of 10. Inconclusive compounds also have PUBCHEM_ACTIVITY_SCORE between 1 and 39.

External ID: PROCASPASE3_ACT_EPIABS_1536_1X%ACT PRUN

Protocol: Assay Overview:

The purpose of this assay is to identify compounds that activate procaspase 3 activity. This assay employs a procaspase 3 mutant enzyme, D9A/D28A/D175A (called PC-3 D3A) which is unable to autoproteolyze itself because its aspartic acid cleavage sites have been mutated to alanines. The mutant has a fully functional active site that can process the peptidic Ac-DEVD-pNA chromogenic substrate. Cleavage of substrate by procaspase 3 hydrolyzes the bond between the aspartic acid and p-nitroaniline, leading to release of yellow p-nitroaniline and an increase in well absorbance at 405 nm. In this assay, PC-3 D3A enzyme is pre-incubated with test compounds, followed by addition of substrate and measurement of well epi-absorbance. As designed, compounds that activate procaspase 3 activity will increase substrate hydrolysis, leading to an increase in well absorbance. Compounds are tested in singlicate at a nominal concentration of 8.5 uM.

Protocol Summary:

Prior to the start of the assay, 2.5 uL of zinc-free Assay Buffer (50 mM HEPES, 300 mM NaCl, pH 7.4, 0.01% Triton-X 100) containing 2 uM of PC-3 D3A protein were dispensed into 1536 microtiter plates. Next, 43 nL of test compound in DMSO or DMSO alone (0.8% final concentration) were added to the appropriate wells and incubated for 1 hour at 25 C.

The assay was started by dispensing 2.5 uL of 400 uM Ac-DEVD-pNA in Assay Buffer to all wells. Plates were centrifuged and after 2 hours of incubation at 25 C, epi-absorbance was read on the EnVision plate reader using a photometric filter set (excitation = 405 nm, emission = 450 nm) and a dichroic mirror with 425 nm cutoff. Fluorescence emission was read at 10 flashes per well at two time points (0 minutes and 120 minutes).

Prior to further calculations, the following formula was used to calculate absorbance:

Abs = ( -Log10( ( [ Raw2 ] / [ Mean Reference2 ] ) ) - ( -Log10 ( ( [ Raw1 ] ) / [ Mean Reference ] ) )

Where:

Raw1 is defined as the read at T0 minutes.
Raw2 is defined as the read at T120 minutes.
Mean Reference is defined as a mean of values from wells containing buffer only at T0.
Mean Reference2 is defined as a mean of values from wells containing buffer only at T120.

The percent activation for each compound was calculated as follows:

% Activation = ( ( Ratio_Test_Compound - Median_Ratio_Low_Control ) / ( Median_Ratio_High_Control - Median_Ratio_Low_Control ) ) * 100

Where:

Test_Compound is defined as wells containing test compound.
Low_Control is defined as wells containing DMSO.
High_Control is defined as wells containing DMSO and 5 uM PC-3 D3A.

A mathematical algorithm was used to determine nominally activating compounds in the primary screen. Two values were calculated: (1) the average percent activation of all compounds tested, and (2) three times their standard deviation.The sum of these two values was used as a cutoff parameter, i.e. any compound that exhibited greater % activation than the cutoff parameter was declared active.

PubChem Activity Outcome and Score:

The reported PubChem Activity Score has been normalized to 100% observed primary activation. Negative % activation values are reported as activity score zero.

The PubChem Activity Score range for active compounds is 100-9, and for inactive compounds 9-0.

List of Reagents:

Recombinant PC-3 D3A (procaspase 3 enzyme) (Assay Provider)
Assay Buffer (Assay Provider)
Chromogenic Substrate (Ac-DEVD-pNA) (Assay Provider)
1536 SWSN plates (Corning, part 7254)

Comment: Due to the increasing size of the MLPCN compound library, this assay may have been run as two or more separate campaigns, each campaign testing a unique set of compounds. All data reported were normalized on a per-plate basis. Possible artifacts of this assay can include, but are not limited to: dust or lint located in or on wells of the microtiter plate, and compounds that modulate well absorbance. All test compound concentrations reported above and below are nominal; the specific test concentration(s) for a particular compound may vary based upon the actual sample provided by the MLSMR.

External ID: SBCCG-A1015-NR3A-Primary-Assay

Protocol: A.#Brief Description of the Assay
This assay attempts to identify small molecule compound binding to NR3A LBD using differential scanning fluorimetry assay. The assay is performed format using Applied Biosystems 384-well plates (cat #4309849) on ViiA7 qPCR instrument (Thermo-Fisher Scientific).

B.#Assay reagent components:
1.#Assay buffer: 20 mM HEPES, pH 7.5, 200 mM NaCl
2.#NR3A LBD working solution in the assay buffer
3.#NR3A LBD with glycine working solution in the assay buffer
4.#Sypro Orange working solution in the assay buffer
5.#Compounds in 100% DMSO

C.#Step-by-step protocol:
1.#Reagent dispenses
a.#Add compound aliquots to the wells in columns 3-24
b.#Add DMSO aliquots to the wells in columns 1-2
c.#Dispense 5 uL of NR3A LBD working solution into columns 2-24
d.#Dispense 5 uL of NR3A LBD with glycine working solution to column 1
e.#Dispense 5 uL of Sypro Orange with glycine solution to columns 1-24
2.#Perform assay by ramping temperature and measuring concomitant changes in fluorescence
3.#Determine Tm corresponding to the maximum of the first derivative of fluorescence
D.#Final concentration of reagents in the assay wells
1.#1.25 uM NR3A LBD (all wells)
2.#x5 Sypro Orange (all wells)
3.#25 uM tested compounds (wells in columns 3-24)
4.#0.25% DMSO (all wells)
E.#Plate Map:
1.#Positive (high Tm) control in column 1
2.#Negative (low Tm) control in column 2.
3.#Test wells in columns 3-24.

Comment: %Activity = (Melting temperature of compound well - Average melting temperature of negative control well)/(Melting temperature of positive control wells - Melting temperature of negative control wells)*100%.

Compounds that demonstrated %Activity >= 10% at 25 uM concentration are defined as actives in this assay.

Activity Scoring
The score is correlated with % activity in the assay:
a. If outcome of the primary screen is inactive, then the assigned score is 0
b. If outcome of the primary screen is active, then the assigned score is 20

External ID: epac1-inhibitor-v

Protocol: Briefly, three uL of reagents (100 nM EPAC1, 250 nM RAP1B-BODIPY-GDP, 50 uM GDP) were dispensed into a 1536-well Greiner black solid-bottom medium binding assay plate. Controls and test compounds (23 nL) were transferred to the plate via a Kalypsys pin tool equipped with a 1536-pin array. The plates were centrifuged at 1,000 rpm for 15 seconds followed by 5 minute incubation at room temperature. The assay plates were read at 5 minute intervals for 30 minutes in the ViewLux plate reader using 480nm excitation and 540nm emission filters. The results were normalized to the agonist positive control ATA and DMSO.

Comment: Disclaimer:
Although all reasonable efforts have been made to ensure the accuracy and reliability of the data, caution should be exercised when interpreting the results as artifacts are possible from nonspecific effects such as assay signal interference. The curve fitting and activity calls presented here are based on the NCATS analysis methods.

Compound Ranking:
1. Compounds are first classified as having full titration curves, partial modulation, partial curve (weaker actives), single point activity (at highest concentration only), or inactive. For this assay, apparent inhibitors are ranked higher than compounds that showed apparent activation.
2. For all inactive compounds, with a ratio activity curve class of 4, PUBCHEM_ACTIVITY_SCORE is 0. For all active compounds, a score range was given for each curve class type given above. Active compounds have PUBCHEM_ACTIVITY_SCORE between 40 and 100. For a ratio activity curve class = -1.1, score = 80+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == -1.2 && abs(ratio.max_response) > 6*10, score = 60+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == -2.1 || ( ratio.curve_class==-2.2 && abs(ratio.max_response) > 6*10), score = 40+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == -1.2 || ratio.curve_class == -2.2, score = 20+abs((log_ac50+4.5)*inf_activity/20). Inconclusive compounds, with a donor curve class other than 4, have PUBCHEM_ACTIVITY_SCORE of 10. Inconclusive compounds have PUBCHEM_ACTIVITY_SCORE between 1 and 39.

External ID: PolI100

Protocol: Three microliters of reagents (buffer in column 3 and 4 as negative control and 10 nM Pol iota in columns 1, 2, and 5-48) will be dispensed into 1,536-well black solid-bottomed plate. Compounds (23 nL) will be transferred via Kalypsys pin tool equipped with 1536-pin array. The plates will then be incubated for 15 min at room temperature, and 1 muL substrate (50 nM final concentration) will be added to start the reaction and kinetically read twice at 0 min and 10 min on the Viewlux reader.

Comment: Compound Ranking:

1. Compounds are first classified as having full titration curves, partial modulation, partial curve (weaker actives), single point activity (at highest concentration only), or inactive. See data field "Curve Description". For this assay, apparent inhibitors are ranked higher than compounds that showed apparent activation.
2. For all inactive compounds, PUBCHEM_ACTIVITY_SCORE is 0. For all active compounds, a score range was given for each curve class type given above. Active compounds have PUBCHEM_ACTIVITY_SCORE between 40 and 100. Inconclusive compounds have PUBCHEM_ACTIVITY_SCORE between 1 and 39. Fit_LogAC50 was used for determining relative score and was scaled to each curve class' score range.

External ID: epac2-activator-v2

Protocol: Briefly, three uL of reagents (100 nM EPAC2, 250 nM RAP1B-BODIPY-GDP, 50 uM GDP) were dispensed into a 1536-well Greiner black solid-bottom medium binding assay plate. Controls and test compounds (23 nL) were transferred to the plate via a Kalypsys pin tool equipped with a 1536-pin array. The plates were centrifuged at 1,000 rpm for 15 seconds followed by 5 minute incubation at room temperature. The assay plates were read at 5 minute intervals for 30 minutes in the ViewLux plate reader using 480nm excitation and 540nm emission filters. The results were normalized to the agonist positive control of 6.5 mM cAMP.

Comment: Disclaimer:
Although all reasonable efforts have been made to ensure the accuracy and reliability of the data, caution should be exercised when interpreting the results as artifacts are possible from nonspecific effects such as assay signal interference. The curve fitting and activity calls presented here are based on the NCATS analysis methods.

Compound Ranking:
1. Compounds are first classified as having full titration curves, partial modulation, partial curve (weaker actives), single point activity (at highest concentration only), or inactive. For this assay, apparent activators are ranked higher than compounds that showed apparent inhibition.
2. For all inactive compounds, with a ratio activity curve class of 4, PUBCHEM_ACTIVITY_SCORE is 0. For all active compounds, a score range was given for each curve class type given above. Active compounds have PUBCHEM_ACTIVITY_SCORE between 40 and 100. For a ratio activity curve class = 1.1, score = 80+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == 1.2 && abs(ratio.max_response) > 6*10, score = 60+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == 2.1 || ( ratio.curve_class==-2.2 && abs(ratio.max_response) > 6*10), score = 40+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == 1.2 || ratio.curve_class == 2.2, score = 20+abs((log_ac50+4.5)*inf_activity/20). Inconclusive compounds, with a donor curve class other than 4, have PUBCHEM_ACTIVITY_SCORE of 10. Inconclusive compounds also have PUBCHEM_ACTIVITY_SCORE between 1 and 39.

External ID: GDH-TPI_INH_ABS_1536_1X%INH CSRUN

Protocol: Assay Overview:

The purpose of this biochemical counterscreen is to determine whether compounds act as absorbance assay artifacts or are non-selective. This assay also serves as a counterscreen for a set of ongoing high throughput primary experiments entitled, "Absorbance-based biochemical primary high throughput screening assay to identify inhibitors of the aldolase of M. tuberculosis."

This counterscreen is similar in format to the aforementioned assay with the only two following differences: (i) the fructose-1,6-bisphosphate substrate is replaced with glyceraldehyde 3 phosphate, a product of its conversion by FBA and (ii) no (FBA) is used. The counterscreen hence recapitulates the two steps involved in the monitoring of FBA activity through the conversion of FB into the triose product glyceraldehyde 3 phosphate (G3P), which would be converted to dihydroxyacetone phosphate (DHAP) by the helper enzyme triose phosphate isomerase (TPI). A second helper enzyme, glycerophosphate dehydrogenase (GDH), converts the dihydroxyacetone phosphate to glycerol-3-phosphate with the concomitant oxidation of NADH to NAD, which is monitored by measuring the absorbance at 340 nm. In this new assay format, the A340 is independent of FBA activity, hence compounds that reduce absorbance at 340 nm are either absorbance artifacts or helper enzyme inhibitors that will not be pursued. Compounds are tested in singlicate at a final nominal concentration of 4.78 uM.

Protocol Summary:

Prior to the start of the assay, 5 uL /well of Buffer A (50 mM HEPES, 0.01% Triton X-100, 10% Glycerol, pH8.0) supplemented with 400 nM ZnCl2,240 uM NADH and the helper enzymes GDH-TPI (4 U/mL) was dispensed into all wells of a 1536-well plate except the "No enzyme" wells that contained the same supplemented buffer but no GDH-TPI enzymes. Next, 48 nL of test compounds were then delivered in each well using a PinTool. The assay was then initiated by dispensing 5 uL of Buffer A supplemented with 240 uM of the substrate glyceraldehyde-3-phosphate (G3P). Plates were incubated at room temperature for 20 minutes before A340 was measured using the EnVision plate reader (Perkin Elmer).

The percent inhibition for each compound was calculated as follows:

%Inhibition = 100 * ( ( Test_Compound - Median_Low_Control ) / ( Median_High_Control - Median_Low_Control ) )

Where:

Test_Compound is defined as wells treated with test compounds.
Low_Control is defined as wells treated with DMSO.
High_Control is defined as wells with no GDH-TPI enzyme.

A mathematical algorithm was used to determine nominally inhibiting compounds in the primary screen. Two values were calculated for each assay plate: (1) the average percent inhibition of test compound wells and (2) three times their standard deviation. The sum of these two values was used as a cutoff parameter for each plate, i.e. any compound that exhibited greater % inhibition than the cutoff parameter was declared active.

PubChem Activity Outcome and Score:

The reported PubChem Activity Score has been normalized to 100% observed inhibition. Negative % inhibition values are reported as activity score zero.

The PubChem Activity Score range for active compounds is 100-13, and for inactive compounds 13-0.

List of Reagents:

ZnCl2 (Fisher Scientific, part Z33-500)
NADH (EMD Biosciences, part 481913)
GDH-TPI (Sigma, part G1881)
HEPES (EMD Biosciences, part EM-5310)
Triton X-100 (Sigma, part T8787)
Glycerol (Fisher, part AC327255000)
Glyceraldehyde-3-phosphate (Sigma, part D7137)
1536-well plates (Aurora, part 1091-11020-S)

Comment: Due to the increasing size of the MLPCN compound library, this assay may have been run as two or more separate campaigns, each campaign testing a unique set of compounds. In this case the results of each separate campaign were assigned "Active/Inactive" status based upon that campaign's specific compound activity cutoff value. All data reported were normalized on a per-plate basis. Possible artifacts of this assay can include, but are not limited to: dust or lint located in or on wells of the microtiter plate, and compounds that quench or emit absorbance within the well. All test compound concentrations reported are nominal; the specific concentration for a particular test compound may vary based upon the actual sample provided by the MLSMR

External ID: PolE100

Protocol: Three microliters of reagents (buffer in column 3 and 4 as negative control and 10 nM Pol eta in columns 1, 2, and 5-48) were dispensed into a 1,536-well black solid-bottomed plate. Compounds (23 nL) were transferred via Kalypsys pin tool equipped with 1536-pin array. The plates were then incubated for 15 min at room temperature, and 1 muL substrate (50 nM final concentration) was added to start the reaction and kinetically read twice at 0 min and 10 min on the Viewlux reader

Comment: Compound Ranking:

1. Compounds are first classified as having full titration curves, partial modulation, partial curve (weaker actives), single point activity (at highest concentration only), or inactive. See data field "Curve Description". For this assay, apparent inhibitors are ranked higher than compounds that showed apparent activation.
2. For all inactive compounds, PUBCHEM_ACTIVITY_SCORE is 0. For all active compounds, a score range was given for each curve class type given above. Active compounds have PUBCHEM_ACTIVITY_SCORE between 40 and 100. Inconclusive compounds have PUBCHEM_ACTIVITY_SCORE between 1 and 39. Fit_LogAC50 was used for determining relative score and was scaled to each curve class' score range.

External ID: epac2-inhibitor-v2

Protocol: Briefly, three uL of reagents (100 nM EPAC2, 250 nM RAP1B-BODIPY-GDP, 50 uM GDP) were dispensed into a 1536-well Greiner black solid-bottom medium binding assay plate. Controls and test compounds (23 nL) were transferred to the plate via a Kalypsys pin tool equipped with a 1536-pin array. The plates were centrifuged at 1,000 rpm for 15 seconds followed by 5 minute incubation at room temperature. The assay plates were read at 5 minute intervals for 30 minutes in the ViewLux plate reader using 480nm excitation and 540nm emission filters. The results were normalized to the agonist positive control of 6.5 mM cAMP.

Comment: Disclaimer:
Although all reasonable efforts have been made to ensure the accuracy and reliability of the data, caution should be exercised when interpreting the results as artifacts are possible from nonspecific effects such as assay signal interference. The curve fitting and activity calls presented here are based on the NCATS analysis methods.

Compound Ranking:
1. Compounds are first classified as having full titration curves, partial modulation, partial curve (weaker actives), single point activity (at highest concentration only), or inactive. For this assay, apparent inhibitors are ranked higher than compounds that showed apparent activation.
2. For all inactive compounds, with a ratio activity curve class of 4, PUBCHEM_ACTIVITY_SCORE is 0. For all active compounds, a score range was given for each curve class type given above. Active compounds have PUBCHEM_ACTIVITY_SCORE between 40 and 100. For a ratio activity curve class = -1.1, score = 80+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == -1.2 && abs(ratio.max_response) > 6*10, score = 60+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == -2.1 || ( ratio.curve_class==-2.2 && abs(ratio.max_response) > 6*10), score = 40+abs((log_ac50+4.5)*inf_activity/20). For ratio.curve_class == -1.2 || ratio.curve_class == -2.2, score = 20+abs((log_ac50+4.5)*inf_activity/20). Inconclusive compounds, with a donor curve class other than 4, have PUBCHEM_ACTIVITY_SCORE of 10. Inconclusive compounds have PUBCHEM_ACTIVITY_SCORE between 1 and 39.

External ID: 2070-01_Inhibitor_SinglePoint_HTS_Activity

Protocol: Protocol:
ASSAY PROCEDURE FOR HEDGEHOG AUTOPROCESSING

Buffer A: 20 mM sodium phosphate, pH 7.5, 0.5 M NaCl

Buffer B: 20 mM sodium phosphate, pH 7.5, 0.5 M NaCl, 8 M urea
This is prepared by adding 48 g of urea (enzyme grade) to 50 ml of double-strength Buffer A and adjusting volume to 100 ml with H2O.


Buffer D: 20 mM sodium phosphate, pH 7.0, 0.5 M NaCl, and 0.5 M arginine
(2.0 M arginine, pH 7.0, is prepared by dissolving 211 g of L-arginine hydrochloride (obtained from Research Organics) in 300 ml of H2O, adjusting pH to 7.0 with NaOH, and adjusting volume to 500 ml)



REAGENTS:
Urea - American Bioanalytical AB02100
Arginine Hydrochloride - American Bioanalytical AB000164
TCEP [Tris(2-carboxyethyl)phosphine hydrochloride] - Sigma C4706
DM-MEA [2-(Dimethylamino)ethanethiol] - Aldrich D141003 (very hygroscopic)
Cholesterol - Sigma C8667
FLAsH-EDT2-Invitrogen T34561

CELL DISRUPTION:

Suspend the cells from 50 ml of E. coli [Rosetta 2 (DE3)/pET45Dmel710#2] in 3 ml of Buffer A +
1 mM PMSF and disrupt by passing twice through the small French pressure cell. Centrifuge in 12 ml Sorvall tubes at 12,000 rpm for 30 min. and collect the pellet (inclusion bodies). The pellet is washed twice by resuspending in 4 ml of Buffer A + 1 mM PMSF and centrifugation at 12,000 rpm for 20 min. The pellet is then then resuspended in 3 ml of Buffer B + 1 mM PMSF to extract the inclusion bodies and centrifuged at 12,000 rpm for 20 min. Save the supernatant and extract the pellet a second time with 3 ml of Buffer B + 1 mM PMSF and combine the supernatants. Centrifuge the combined supernatants in the Sorvall at 18,000 rpm for 60 min to remove insoluble material and yield the solubilized inclusion bodies (IB). Save inclusion bodies at 4 degrees C after diluting about 10% with Buffer A to avoid crystallization of urea.

Typically, the protein concentration of the inclusion bodies is 1 mg/ml. The material is stable on storage at 4 degrees C for at least a month and can be kept frozen at -80 degrees C in 1 ml portions indefinitely.


Dilution Buffer:
297 ml of Buffer D
3 ml of 0.1 M TCEP
300 ml Final

Substrate mix
6.5 ml of 26 mM cholesterol in 95% EtOH
2.0 ml of 1% Triton X-100
41.5 ml of H2O
50 ml + 200 ml Dilution Buffer (cholesterol = 680 microM) - Dilute immediately before use

Control mix
0.8 ml of 1% Triton X-100
19.2 ml of H2O
20 ml + 80 ml Dilution Buffer (No cholesterol)

IB mix
13.2 ml Hedgehog protein ( approximately 1.65 mg/ml) [12 ml form prep of 10.05.11, 2 ml from prep of 10.05.10]
198 ml Buffer D (
room temp)
2.2 ml of 0.1 M TCEP
2.2 ml of 0.1 M DM-MEA
2.2 ml of 0.17 mM FlAsH
2.2 ml of H2O
220 ml final




Incubate at 25*C for 2 h. Dialyze against 3 X 1 liter Buffer D + 1 mM TCEP (10 ml of 0.1 M TCEP per liter) for 6 h - 14h. Recommended dialysis tubing: SpectraPor MWCO 8,000, flat width = 12 mM (VWR 25223-650). Readjust volume to 220 ml after dialysis.The dialyzed Hh Protein Cocktail can be stored at 4 degrees C for at least 5 days with negligible loss of activity. It should be stable at room temperature for at least 12 h.




Dispense 35 microl per well. Add IB mix first to entire plate. Wait 30 min before adding cholesterol, while control mix (35ul) is added to columns 23&24.

Then add substrate mix to columns 1-22, 40 min after adding protein. Fluorescence polarization was measured after 1 hour incubation at 25C using Tecan Safire 2 microplate reader (Tecan, Mannedorf, Switzerland) with excitation at 390 nm and emission at 550
nm.

Comment: PRESENCE OF CONTROLS: Neutral control wells (NC) and positive control wells (PC) were included on every plate.

EXPECTED OUTCOME: Active compounds result in increasing readout signal.

NORMALIZATION:
The raw signals of the plate wells were normalized using the 'Neutral Controls Minus Inhibitors' method in Genedata Assay Analyzer (v7.0.3):
The median raw signal of the intraplate neutral control wells was set to a normalized activity value of 0.
The median raw signal of the intraplate positive control wells was set to a normalized activity value of -100.
Experimental wells values were scaled to this range.

PATTERN CORRECTION: No plate pattern correction algorithm from Genedata Condoseo (v.7.0.3) was applied.

PUBCHEM_ACTIVITY_SCORE:
This was set as equal to the mean of the normalized sample replicate activities, rounded to the nearest integer .
The minimum PUBCHEM_ACTIVITY_SCORE required for a compound to be called a hit (the activity threshold, or AT) was set to be three standard deviations above the mean neutral control value.

PERCENTAGE OF ACTIVE REPLICATES:
For each sample, the percentage of replicates (PCT_ACTIVE_REP) which had activity scores >= AT was determined.
The minimum percentage of replicates required for a compound to be called a hit (PAR_T) was set at -50.

PUBCHEM_ACTIVITY_OUTCOME:
Samples passing BOTH threshold criteria were assigned an outcome of 2 (active):
PUBCHEM_ACTIVITY_SCORE >= AT, and PCT_ACTIVE_REP >= PAR_T

Samples passing NEITHER threshold criteria were assigned an outcome of 1 (inactive):
PUBCHEM_ACTIVITY_SCORE < AT, and PCT_ACTIVE_REP < PAR_T

Samples passing AT only were assigned an outcome of 2 (active) :
PUBCHEM_ACTIVITY_SCORE >= AT, and PCT_ACTIVE_REP < PAR_T

tSamples passing PAR_T only were assigned an outcome of 2 (active) :
PUBCHEM_ACTIVITY_SCORE < AT, and PCT_ACTIVE_REP >= PAR_T

External ID: UIHTS20180925

Protocol: Assay overview:
The purpose of this assay is to identify test compounds that differentially kill either epithelial cells or mesenchymal cells, critical components of EMT. The PC-3E+ and TEM4-18 cell lines, characterized as epithelial cells and mesenchymal cells respectively, were established in Henry Lab (Ref 1). For potential discriminative modulators of EMT, the two cells lines were labeled with GFP and mCherry respectively, and co-cultured together to eliminate those hits that non-discriminatingly kill both epithelial cells and mesenchymal cells by cytotoxicity irrelevant to the EMT properties.
Protocol for the EMT project:
The primary screening data were generated as described in HTS assay protocol table (Ref 2).

Table 1: HTS assay protocol table
Step Parameter Value Description
1. Plate cells 200 uL By MultiFlo. PC3E GFP 2,000 cells/ well and TEM418 mCherry 2,000 cells/well (1:1). Overnight incubation
2. Remove media Flip the plate
3. Add fresh media 150 uL By MultiFlo
4. Controls 200 uL C01-H01, C12 -H12, Hygromycin dose response from H to C were positive control. Wells A01, B01, A12 and B12 were negative control
5. Library 50 uL MSSP library 1 uM final from middle plate in full media
6. Incubation 72 hrs 37 C and 5% CO2
7. Assay readout GFP and mCherry channel imaging Perkin Elmer Operetta high content imaging system, with Harmony image analysis software.
8. Image analysis Green cells and Read cells counting Normalized to the average cell number of well B1 and B12 (no inhibition of cell viability) controls on each plate to get relative cell viability for each well.
9. Hit selection 11 hits The hit criteria for preferential cell killing are compounds that Redcells_Normalized is lower or equal 0.41, GreenCells_Normalized is higher or equal
0.55, RedCells/GreenCells_Normalized ratio is lower or equal 0.65, and Non-fluorescent by itself for Red cell killing OR Greencells_Normalized is
lower or equal 0.41, RedCells_Normalized is higher or equal 0.46, RedCells/GreenCells_Normalized ratio is higher or equal 1.8 and Non-fluorescent
by itself for Green cell killing.

The primary screening data (imaging data) were translated into Green or Red cell numbers in each well in the data file.

Comment: Preferential killing compounds are considered as active hits (score of 100) when meeting one of two groups of criteria:

1. Compounds that Redcells_Normalized is lower or equal 0.41, GreenCells_Normalized is higher or equal 0.55, RedCells/GreenCells_Normalized ratio is lower or equal 0.65, and Non-fluorescent by itself for Red cell killing.

OR

2. Greencells_Normalized is lower or equal 0.41, RedCells_Normalized is higher or equal 0.46, RedCells/GreenCells_Normalized ratio is higher or equal 1.8 and Non-fluorescent by itself for Green cell killing.

External ID: PolK100

Protocol: Three microliters of reagents (buffer in column 3 and 4 as negative control and 10 nM Pol kappa in columns 1, 2, and 5-48) were dispensed into a 1536-well black solid-bottom plate. Compounds (23 nL) were transferred via Kalypsys pin tool equipped with 1536-pin array. The plates were then incubated for 15 min at room temperature, and 1 uL substrate (50 nM final concentration) were then added to start the reaction and kinetically read twice at 0 min and 10 min on the Viewlux reader

Comment: Compound Ranking:

1. Compounds are first classified as having full titration curves, partial modulation, partial curve (weaker actives), single point activity (at highest concentration only), or inactive. See data field "Curve Description". For this assay, apparent inhibitors are ranked higher than compounds that showed apparent activation.
2. For all inactive compounds, PUBCHEM_ACTIVITY_SCORE is 0. For all active compounds, a score range was given for each curve class type given above. Active compounds have PUBCHEM_ACTIVITY_SCORE between 40 and 100. Inconclusive compounds have PUBCHEM_ACTIVITY_SCORE between 1 and 39. Fit_LogAC50 was used for determining relative score and was scaled to each curve class' score range.